Difference between revisions of "ASIC design optimizations"
m (→Planned tests) |
(→Planned tests) |
||
Line 7: | Line 7: | ||
[[Image:hvplateau_ch15.jpg|thumb|none|400px|HV-curve,the count is normalized to 100s measurements.]] | [[Image:hvplateau_ch15.jpg|thumb|none|400px|HV-curve,the count is normalized to 100s measurements.]] | ||
− | Below galleries of pulses are shown for different HV: | + | Below galleries of pulses are shown for different HV (on the left channel 2, on the right channel 15) -- remember everything above 1V is an overflow on the fADC: |
** 1600 V | ** 1600 V | ||
+ | {| border="1" cellpadding="2" | ||
+ | |- | ||
+ | |width="415pt"|[[Image:hv-1600-ch2.jpg|thumb|none|400px|Gallery of pulses of channel 2.]] | ||
+ | |width="415pt"|[[Image:hv-1600-ch15.jpg|thumb|none|400px|Gallery of pulses of channel 15.]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | ** 1650 V | ||
+ | {| border="1" cellpadding="2" | ||
+ | |- | ||
+ | |width="415pt"|[[Image:hv-1650-ch2.jpg|thumb|none|400px|Gallery of pulses of channel 2.]] | ||
+ | |width="415pt"|[[Image:hv-1650-ch15.jpg|thumb|none|400px|Gallery of pulses of channel 15.]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | ** 1700 V | ||
+ | {| border="1" cellpadding="2" | ||
+ | |- | ||
+ | |width="415pt"|[[Image:hv-1700-ch2.jpg|thumb|none|400px|Gallery of pulses of channel 2.]] | ||
+ | |width="415pt"|[[Image:hv-1700-ch15.jpg|thumb|none|400px|Gallery of pulses of channel 15.]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | ** 1750 V | ||
+ | {| border="1" cellpadding="2" | ||
+ | |- | ||
+ | |width="415pt"|[[Image:hv-1750-ch2.jpg|thumb|none|400px|Gallery of pulses of channel 2.]] | ||
+ | |width="415pt"|[[Image:hv-1750-ch15.jpg|thumb|none|400px|Gallery of pulses of channel 15.]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | ** 1800 V | ||
+ | {| border="1" cellpadding="2" | ||
+ | |- | ||
+ | |width="415pt"|[[Image:hv-1800-ch2.jpg|thumb|none|400px|Gallery of pulses of channel 2.]] | ||
+ | |width="415pt"|[[Image:hv-1800-ch15.jpg|thumb|none|400px|Gallery of pulses of channel 15.]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | ** 1850 V | ||
+ | {| border="1" cellpadding="2" | ||
+ | |- | ||
+ | |width="415pt"|[[Image:hv-1850-ch2.jpg|thumb|none|400px|Gallery of pulses of channel 2.]] | ||
+ | |width="415pt"|[[Image:hv-1850-ch15.jpg|thumb|none|400px|Gallery of pulses of channel 15.]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | ** 1900 V | ||
+ | {| border="1" cellpadding="2" | ||
+ | |- | ||
+ | |width="415pt"|[[Image:hv-1900-ch2.jpg|thumb|none|400px|Gallery of pulses of channel 2.]] | ||
+ | |width="415pt"|[[Image:hv-1900-ch15.jpg|thumb|none|400px|Gallery of pulses of channel 15.]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | ** 1950 V | ||
+ | {| border="1" cellpadding="2" | ||
+ | |- | ||
+ | |width="415pt"|[[Image:hv-1950-ch2.jpg|thumb|none|400px|Gallery of pulses of channel 2.]] | ||
+ | |width="415pt"|[[Image:hv-1950-ch15.jpg|thumb|none|400px|Gallery of pulses of channel 15.]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | ** 2000 V | ||
+ | {| border="1" cellpadding="2" | ||
+ | |- | ||
+ | |width="415pt"|[[Image:hv-2000-ch2.jpg|thumb|none|400px|Gallery of pulses of channel 2.]] | ||
+ | |width="415pt"|[[Image:hv-2000-ch15.jpg|thumb|none|400px|Gallery of pulses of channel 15.]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
Revision as of 15:59, 30 April 2008
Planned tests
- High Voltage plateau === done
Gas: Ar-CO2 87%-13% gas mixture. Setup: the signal after the shaper was inverted and fed to a discriminator. The HV was changed and the signals above threshold where counted (normalized to 100s measure time). The result:
Below galleries of pulses are shown for different HV (on the left channel 2, on the right channel 15) -- remember everything above 1V is an overflow on the fADC:
- 1600 V
- 1650 V
- 1700 V
- 1750 V
- 1800 V
- 1850 V
- 1900 V
- 1950 V
- 2000 V
- (absolute) Gas gain as a function of High Voltage
Source measurement using Sr-90 (e-) or 55-Fe (X-rays) (if we have it) / or using cosmic rays? -- Estimated time: 1 day -- if we have a good source
- Dynamic range + amplitude distributions
1 week measure with horizontal chamber + 1 week measure with tilted chamber. For amplitude distributions we need to have modified shapers. -- Estimated time: 2 weeks
- Collection of gallery of pulses
I found 4 pulse galleries, measured directly after the pre-amplifier made by Gerard when he was here, they are shown below: