Difference between revisions of "Tagger trigger timing"
From GlueXWiki
m |
m |
||
(3 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
− | Below is tagger trigger timing information I got from Eugene Pasyuk. Note that cables are trimmed so the sum of all delays is the same for all T-counters<br><br> | + | Below is tagger trigger timing information I got from Eugene Pasyuk. Note that cables are trimmed so the sum of all delays is the same for all T-counters. This is calculated using existing cables.<br><br> |
<table width="80%" cellspacing="2" cellpadding="2" border="1"> | <table width="80%" cellspacing="2" cellpadding="2" border="1"> | ||
Line 43: | Line 43: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td valign="top"> | + | <td valign="top">150 ns<br></td> |
− | <td valign="top">cable to BCAL Trigger Supervisor | + | <td valign="top">cable to BCAL Trigger Supervisor<br></td> |
</tr> | </tr> | ||
<tr> | <tr> | ||
Line 51: | Line 51: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td valign="top"> | + | <td valign="top">50 ns<br></td> |
− | <td valign="top"> | + | <td valign="top">ADC gate generation, cables to ADC crate, ADC internal<br></td> |
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td valign="top">''' | + | <td valign="top">'''325 + 150 ns'''<br></td> |
<td valign="top">'''total delay'''<br></td> | <td valign="top">'''total delay'''<br></td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
<br> | <br> | ||
− | Note that the photon flight time from the radiator to the BCAL detector is | + | Note that the photon flight time from the radiator to the BCAL detector is 115 ns, and that the RadPhi setup has 300 ns delay cables (straight, or 100+200 using a patch panel). |
+ | |||
+ | Thus using existing cables the trigger delay is 325+150=475 ns minus the flight time 115 ns gives 360 ns, longer than the 300 ns ADC delay cables. | ||
− | + | See [[Overall tagger timing]] for further discussion. |
Latest revision as of 14:16, 21 July 2006
Below is tagger trigger timing information I got from Eugene Pasyuk. Note that cables are trimmed so the sum of all delays is the same for all T-counters. This is calculated using existing cables.
Delay |
Location |
25 ns |
electron flight time tagger radiator to farthest T-counter |
20 ns |
internal T-counter PMT |
50 ns |
cable to CFD |
15 ns |
internal CFD |
5 ns |
cable to L-R coincidence logic module |
5 ns |
internal L-R coincidence logic module |
10 ns |
cable to Master Or module |
20 ns |
internal MOR |
80 ns |
cable to forward carriage |
150 ns |
cable to BCAL Trigger Supervisor |
45 ns |
internal Trigger Supervisor |
50 ns |
ADC gate generation, cables to ADC crate, ADC internal |
325 + 150 ns |
total delay |
Note that the photon flight time from the radiator to the BCAL detector is 115 ns, and that the RadPhi setup has 300 ns delay cables (straight, or 100+200 using a patch panel).
Thus using existing cables the trigger delay is 325+150=475 ns minus the flight time 115 ns gives 360 ns, longer than the 300 ns ADC delay cables.
See Overall tagger timing for further discussion.