Difference between revisions of "Minutes 2-21-2007"
From GlueXWiki
(Minutes for 2/21/07 FDC weekly meeting) |
|||
(2 intermediate revisions by the same user not shown) | |||
Line 3: | Line 3: | ||
Date: February 21, 2007 | Date: February 21, 2007 | ||
− | Participants: Daniel, Tim, Fernando | + | Participants: Daniel, Tim, Fernando, Simon, Brian, Chuck, Roger, John Schaapman, Lars Holm |
− | Next Meeting: | + | Next Meeting: Monday, March 5, 2007 @ 11:00 a.m. |
----------------------------------------------------------------------- | ----------------------------------------------------------------------- | ||
− | + | ==Design Issues== | |
- We discussed the possible repositioning of the daughter board | - We discussed the possible repositioning of the daughter board | ||
connectors for the cathode in the middle of the cathode sandwich. | connectors for the cathode in the middle of the cathode sandwich. | ||
Line 21: | Line 21: | ||
where the connector can be soldered into place. | where the connector can be soldered into place. | ||
- The tricky part is that we will have to cut flaps into the | - The tricky part is that we will have to cut flaps into the | ||
− | cathode board and route this flap through a cut-out on the | + | cathode board and route this flap through a cut-out on the G10 |
frame. The flap would be threaded though the cut-out and glued | frame. The flap would be threaded though the cut-out and glued | ||
− | to the back side of the | + | to the back side of the G10 frame. Once glued down, the connector |
could be soldered on. | could be soldered on. | ||
- Note that the cathode board material comes from the manufacturer | - Note that the cathode board material comes from the manufacturer | ||
Line 34: | Line 34: | ||
act to prevent the board from ripping once the cut is made. | act to prevent the board from ripping once the cut is made. | ||
− | + | ==Ground Plane Thickness== | |
- Gerard Visser did some thinking on the ground plane issue based | - Gerard Visser did some thinking on the ground plane issue based | ||
on the sample that Brian had provided him. Gerard states that | on the sample that Brian had provided him. Gerard states that | ||
Line 41: | Line 41: | ||
use. | use. | ||
− | + | ==Cathode Mechanical Mockups== | |
- Brian has left the cathode sandwich with the JLab Survey folks as | - Brian has left the cathode sandwich with the JLab Survey folks as | ||
they had some additional things that they wanted to work on | they had some additional things that they wanted to work on | ||
Line 59: | Line 59: | ||
the order. | the order. | ||
− | + | ==Circuit Board Material== | |
- We discussed the HVPF board idea again (as a review). Fernando | - We discussed the HVPF board idea again (as a review). Fernando | ||
will discuss this with Chris Cuevas at some point and will look | will discuss this with Chris Cuevas at some point and will look | ||
into getting us a quote on boards made with this material. | into getting us a quote on boards made with this material. | ||
− | + | ==Drift Chamber Review== | |
- The FDC TDR (Technical Design Document) has been posted on the | - The FDC TDR (Technical Design Document) has been posted on the | ||
GlueX portal and has gone out to the reviewers for the upcoming | GlueX portal and has gone out to the reviewers for the upcoming |
Latest revision as of 09:07, 12 April 2007
FDC Weekly Meeting
Date: February 21, 2007
Participants: Daniel, Tim, Fernando, Simon, Brian, Chuck, Roger, John Schaapman, Lars Holm
Next Meeting: Monday, March 5, 2007 @ 11:00 a.m.
Contents
Design Issues
- We discussed the possible repositioning of the daughter board connectors for the cathode in the middle of the cathode sandwich. - Fernando stated that for the 50-pin connectors, we must use surface-mount components as this is all that is available. - He has found a connector that is only 4-mm thick. This is good news. - Tim had prepared as design sketch (via "foot-CAD") that was used as the basis for our discussions. - The best solution seems to be to use a double-sided cathode board with a via that takes the signals to the back side of the board where the connector can be soldered into place. - The tricky part is that we will have to cut flaps into the cathode board and route this flap through a cut-out on the G10 frame. The flap would be threaded though the cut-out and glued to the back side of the G10 frame. Once glued down, the connector could be soldered on. - Note that the cathode board material comes from the manufacturer with copper on both sides, so the material is not an issue. However the cost will increase due to the fact that we are constructing now a two-sided board with via. Brian will look into the cost increases. - As this approach would involve cutting the cathode boards with scissors (sounds crude, we know), we can lay out copper on board sides of the board to define the region to cut. This will also act to prevent the board from ripping once the cut is made.
Ground Plane Thickness
- Gerard Visser did some thinking on the ground plane issue based on the sample that Brian had provided him. Gerard states that Fernando will have some simulations to run, but basically it looks like this material will do an adequate job and is O.K. to use.
Cathode Mechanical Mockups
- Brian has left the cathode sandwich with the JLab Survey folks as they had some additional things that they wanted to work on regarding the flatness measurement. Brian assured us that the sandwich is safe where it is located. - Brian will start on preparing a stretched cathode tomorrow. The construction should be done and measured by next week. After the plane is constructed, Brian will measure the distortions of the cathode boards by locating some marks that he will put on the kapton before stretching. This will be done via a simple optical technique. - Brian has been told by the folks manufacturing our dummy copper strip circuit boards that they will get the material by Mar. 5 and we should have the boards in our hands about a week later. Brian ordered 20 sets of boards (each set has 3 pieces and makes up one cathode plane). We spec'ed flatness of the kapton for the order.
Circuit Board Material
- We discussed the HVPF board idea again (as a review). Fernando will discuss this with Chris Cuevas at some point and will look into getting us a quote on boards made with this material.
Drift Chamber Review
- The FDC TDR (Technical Design Document) has been posted on the GlueX portal and has gone out to the reviewers for the upcoming Drift Chamber review on Mar. 6-8. - All talks have been posted, but they are still being worked on. You can look at the GlueX portal for the latest versions. - We discussed what show and tell we want for the review. We agreed on the cathode sandwich, the FDC prototype (in a protective box so folks can't touch), and DSC added the cathode planes for the prototype.
Minutes prepared by Daniel. Send any comments or corrections along.