Difference between revisions of "Fall 2016"
From GlueXWiki
(7 intermediate revisions by the same user not shown) | |||
Line 2: | Line 2: | ||
* Perform luminosity scan | * Perform luminosity scan | ||
* Beam and detector conditions: | * Beam and detector conditions: | ||
− | :: - | + | :: - Beam flux 2. - 5. x 10^7 photons/sec. |
:: - Exclude CDC/FDC/TOF at high rate if detectors are not ready (calibrate baselines if needed) | :: - Exclude CDC/FDC/TOF at high rate if detectors are not ready (calibrate baselines if needed) | ||
::: (repeat tests when sub-detectors are ready) | ::: (repeat tests when sub-detectors are ready) | ||
− | * Study L1 rate for various thresholds | + | * Study L1 rate for various trigger thresholds |
:: - Trigger types: FCAL & BCAL (& ST), TAGH & ST, (FCAL, BCAL) | :: - Trigger types: FCAL & BCAL (& ST), TAGH & ST, (FCAL, BCAL) | ||
− | :: - | + | :: - Ajust trigger parameters (busy thresholds, TS trigger inhibit thresholds) |
:: - Check performance of electronics modules at high rate | :: - Check performance of electronics modules at high rate | ||
− | ::: (reveal electronics problems and limiting factors: data rate, etc.) | + | ::: (reveal electronics problems and limiting factors: data transmission rate, etc.) |
− | + | :: - Study L1 trigger rate limitations | |
− | + | * Take data for several thresholds at different luminosity (check efficiency) | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | ::- | + | |
− | + | ||
− | + | ||
− | * | + | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + |
Latest revision as of 08:25, 15 September 2016
Phase III. Performance at high rate
- Perform luminosity scan
- Beam and detector conditions:
- - Beam flux 2. - 5. x 10^7 photons/sec.
- - Exclude CDC/FDC/TOF at high rate if detectors are not ready (calibrate baselines if needed)
- (repeat tests when sub-detectors are ready)
- Study L1 rate for various trigger thresholds
- - Trigger types: FCAL & BCAL (& ST), TAGH & ST, (FCAL, BCAL)
- - Ajust trigger parameters (busy thresholds, TS trigger inhibit thresholds)
- - Check performance of electronics modules at high rate
- (reveal electronics problems and limiting factors: data transmission rate, etc.)
- - Study L1 trigger rate limitations
- Take data for several thresholds at different luminosity (check efficiency)