Difference between revisions of "Tagger Magnetic Field Mapping"
From GlueXWiki
(→Some preliminary ideas about mapping requirements) |
(→Some preliminary ideas about mapping requirements) |
||
Line 2: | Line 2: | ||
# We need to map every region of the field where electrons are transported, but can omit corners where no trajectories go. I attach a crude picture of electron orbits. Maybe Sascha has a better one. [[Image:tagger_electron_orbits_map.png|600px|center]] | # We need to map every region of the field where electrons are transported, but can omit corners where no trajectories go. I attach a crude picture of electron orbits. Maybe Sascha has a better one. [[Image:tagger_electron_orbits_map.png|600px|center]] | ||
# By my previous experience ray-tracing in the Hall B tagger magnet (6 cm gap), I would propose the following. | # By my previous experience ray-tracing in the Hall B tagger magnet (6 cm gap), I would propose the following. | ||
− | #* Uniform field region inside gap (at least 10 cm or 4" away from a field boundary | + | #* Uniform field region inside gap (at least 10 cm or 4" away from a field boundary: |
#** 1" by 1" grid | #** 1" by 1" grid | ||
#* In the vicinity of the long field boundary: | #* In the vicinity of the long field boundary: | ||
#** 1" (parallel to edge) by 0.25" transverse from -10 cm inside to +15 cm outside | #** 1" (parallel to edge) by 0.25" transverse from -10 cm inside to +15 cm outside | ||
#** 1" (parallel to edge) by 1" transverse from +15 cm to +30 cm outside | #** 1" (parallel to edge) by 1" transverse from +15 cm to +30 cm outside | ||
− | #* In the vicinity of the entry face and the full-energy beam exit, cover a region at least 6" (i.e. +/- 3") wide around the trajectories | + | #* In the vicinity of the entry face and the full-energy beam exit, cover a region at least 6" (i.e. +/- 3") wide around the trajectories: |
#** 1" by 1" from 30 cm to 15 cm outside, | #** 1" by 1" from 30 cm to 15 cm outside, | ||
#** 1" by 0.25" transverse from 15 cm outside to 10 cm inside | #** 1" by 0.25" transverse from 15 cm outside to 10 cm inside |
Revision as of 10:16, 14 June 2013
Some preliminary ideas about mapping requirements
- We need to map every region of the field where electrons are transported, but can omit corners where no trajectories go. I attach a crude picture of electron orbits. Maybe Sascha has a better one.
- By my previous experience ray-tracing in the Hall B tagger magnet (6 cm gap), I would propose the following.
- Uniform field region inside gap (at least 10 cm or 4" away from a field boundary:
- 1" by 1" grid
- In the vicinity of the long field boundary:
- 1" (parallel to edge) by 0.25" transverse from -10 cm inside to +15 cm outside
- 1" (parallel to edge) by 1" transverse from +15 cm to +30 cm outside
- In the vicinity of the entry face and the full-energy beam exit, cover a region at least 6" (i.e. +/- 3") wide around the trajectories:
- 1" by 1" from 30 cm to 15 cm outside,
- 1" by 0.25" transverse from 15 cm outside to 10 cm inside
- Uniform field region inside gap (at least 10 cm or 4" away from a field boundary:
- A step of 0.25" near the field boundary means that the maximum field variation per step (which occurs just inside the nominal field boundary) is about 15%. This should be acceptable.
- If the time required for the above is excessive, we could take 2" steps parallel to the long field edge instead of 1".