The BCAL is used to measure the energy and time of showers.

1. Occupancy: This should be approximately flat. There can be hot channels when the baseline drifts. If we're running ask for a pedestal calibration to be done. If we're not running nothing can be done but a very hot channel might explain low efficiency in that area.
2. Hit Efficiency: This should be approximately flat. If there are features we should understand why.
3. Recon. BCAL 1: The histograms are somewhat complicated. The best is to compare them to a good run (the example above.) A difference from the example should be flagged.
4. Recon. BCAL 2: The histograms are somewhat complicated. The best is to compare them to a good run (the example above.) A difference from the example should be flagged.
5. Recon. BCAL 3: The histograms are somewhat complicated. The best is to compare them to a good run (the example above.) A difference from the example should be flagged.
6. BCAL Matching: These plots are for charged particles that are tracked in the drift chambers and projected to the BCAL. The z position along the BCAL can be calculated using the time difference between upstream and downstream hits and compared to the extrapolated position using the drift chambers. The histograms are somewhat complicated. The best is to compare them to a good run (the example above.) A difference from the example should be flagged.
   1. BCAL / Track Delta z (cm): (z determined from time of up - down hits in BCAL) - (z determined from the extrapolation of tracks in the drift chambers)
   2. projected BCAL Hit-Z (cm): z determined by extrapolating tracks in the drift chambers to the BCAL.
   3. Track / BCAL Match Rate: The match rate is the ratio of (number of hits in the BCAL that match the extrapolation of tracks in the drift chamber) / (number of tracks in the drift chamber that point at the BCAL).

CDC Occupancy: There should be a uniform decrease in intensity from the center of the detector outward. Random white cells scattered throughout occur when not enough data were collected, eg empty target runs, trigger tests or no beam. Several contiguous white, dark blue or bright yellow cells which don't match the neighboring cells are a problem.
Time-to-distance: 𝛿, the change in length of the LOCA caused by the straw deformation, is plotted against the measured drift time, t drift . The color scale indicates the distance of closest approach between the track and the wire, obtained from the tracking software. The red lines are contours of the time-to-distance function for constant drift distances from 1.5 mm to 8 mm, in steps of 0.5 mm. They should lie over the top of the dark blue contour lines separating the colour blocks. For the plot of residuals vs drift time, the mean should be less than 15um and the sigma should be less than 150um.
dE/dx: At 1.5GeV/c the fitted peak mean should be within 1% of 2.02 keV/cm.
Efficiency: The efficiency should be 0.98 or higher at 0cm DOCA, gradually fall to 0.97 at approximately 0.5mm and then more steeply through 0.9 at approximately 0.64cm.

Is used for neutral particle detection and pion identification.

1. Check Occupancy:
2. Check FCAL Hits 1:
3. Check FCAL Hits 2:
4. Check FCAL Clusters 1:
5. Check FCAL Recon. 1:
6. Check FCAL Recon. 2:
7. Check Recon. FCAL Matching:

• Calorimeter Timing - The right two plots aren't aligned at zero because not all corrections are currently applied. If there is a 32 ns shift in part of this data, please note this.
• Drift Chamber Timing - In each case, the main peaks should line up at zero, but often have other structures. Ignore the first few bins of the lower left plot (they mostly say something about the noise in the detector). There can be 32 ns shifts in the lower right plot.
• PID System Timing - Nothing to note yet.
• Tagger Timing - The signal to background levels of the left two plots depend on the electron beam current.
• Track Matched Timing - Some overlap here with the tracking timing. The new plots should be centered at zero.
• Tagger/RF Timing - Look for the nice "picket fences" on the right two plots, and that in the bottom left plot each channel peaks at zero.
• Tagger/SC Timing - Should be similar to Tagger/RF Timing but with larger resolution.

Generally in these plots, there will be a difference between diamond and amorphous radiator running. Should probably add some references for non-diamond plots.

• Tracking 1 - There should be some mild dependence on beam current and radiator. Note the spikes in the upper right plot are because we have 4 hypotheses fit to a track by default. The lower left plot does have a peak at zero.
• Tracking 3 -
• Check BCAL pi0 - The fitted peak should near at the correct pi0 mass of 135 MeV.
• Check BCAL/FCAL pi0 - The fitted peak should be lower than the correct pi0 mass, I think because the wrong vertex is used.
• Check p+2pi - The top middle plot should have a sin(2phi) shape for diamond runs. Note that the yields in the top right plot vary from run to run on the order of 10-20%.
• Check p+3pi -Note that the yields in the top right plot vary from run to run on the order of 10-20%.
• Check p+pi0g - Note that the yields in the top right plot vary from run to run on the order of 10-20%.
  • Note that these yields are sensitive to the tagger range used! This changes for different beam current settings.