Difference between revisions of "JLab discriminator"

Revision as of 13:59, 10 December 2011

There is a Hall-B page for JLab discriminator

Manuals

Manual for 16-Channel Discriminator/Scaler VME Module (by J.Proffit), 20-Nov-2002, in (pdf)
Manual for New 16-Channel Discriminator/Scaler VME Module (draft by Ben Raydo), 6-Mar-2009, in (pdf)
Manual for New 16-Channel Discriminator/Scaler VME Module (rev.B by Ben Raydo), 28-May-2010, in (pdf)
Manual for New 16-Channel Discriminator/Scaler VME Module (rev.C by Ben Raydo), 11-Feb-2011, in (pdf)

Example Program

#include "dsc2.h"
int main(){
 vmeOpenDefaultWindows(); /* Map the VME bus memory (For Linux only.). */
 dsc2Init(0xe00000,0,1);  /* Base memory: Only last 2 HW switches are relevant, 
                             the rest are lost due to shift of address. */
                          /* Memory size per board. */
                          /* Number of boards. */
 dsc2Status(0,0);         /* Board number and flag which is not used. */
 dsc2PrintScalers(0,0xff);/* Board number and printing option */
 return(0);
}

Linux VME support

Brian Moffit from CODA group has setup a directory for software for Intel based VME controllers running Linux. README there is a good introduction to the subject.

/site/coda/2.6.1/extensions/linuxvme

RPMs for VME controllers running Linux located in the directory

/site/coda/2.6.1/extensions/linuxvme/RPMS

Available files are:

gefvme-kmod-common-4.1-0.i386.rpm (Development files)
kmod-gefvme-PAE*.rpm (Kernel module)

To install the development RPM without kernel module will require the --nodeps option

rpm -i --nodeps gefvme-kmod-common-4.1-0.i386.rpm

Scalers readout preliminary driver

The current scheme of data flow is the following (from top to down):

Other supplemental files are:

• JLabDiscr_subMain.cpp -- The standard main program
• JLabDiscr_subConfig.c -- hooks for EPICS
• JLabDiscr_subConfig.dbd, JLabDiscr_subrecord.dbd -- DBD files
• dbJLabDiscr.db -- DB file

The output

The output is accessible via PV hallddisc1:JLabDiscr. It has a type of aSubRecord.

Its INPA field setups the card number (Will be configured once during IOC initilaztion).
The VALA is an array of 16 contains scalers of gated triggers.
The VALB is an array of 16 contains scalers of gated TDC values.
The VALC is an array of 16 contains scalers of ungated triggers.
The VALD is an array of 16 contains scalers of ungated TDC values.
The VALE is a signle scalers of gated reference clock.
The VALF is a signle scalers of ungated reference clock.

Instalation

NOTE: The location of files and installation instructions are subject to change. Check back frequently to check the most up-to-date information.

Files are in the directory and subsequent directories: /group/halld/Online/controls/epics/app_nerses

configure

place for include make files

iocBoot

Boot configurations for IOC-es

iocBoot/iocJLabDiscr_sub

Boot configuration directory for JLab Discriminator. The boot configuration is in the file st.cmd

db

Installed DB files directory. Original files are from *App/Db directory.

dbd

Installed DBD files directory. Original files are from *App/src directory.

bin/linux-x86

Installed binaries

lib/linux-x86

Installed libraries

JLabDiscr_subApp/src

Development source files

JLabDiscr_subApp/Db

Original DB files directory