Difference between revisions of "Jul 30, 2015 Calorimetry"

From GlueXWiki
Jump to: navigation, search
(Minutes)
(Minutes)
Line 73: Line 73:
 
##* Will: does the phi modulation without energy selection in FCAL look the same as with an energy cut? Not yet investigated this.
 
##* Will: does the phi modulation without energy selection in FCAL look the same as with an energy cut? Not yet investigated this.
 
# [[Calorimetry F250 Firmware]]  Discussions
 
# [[Calorimetry F250 Firmware]]  Discussions
 +
#* Elton summarized current discussion on the f250 firmware
 +
#* The volume of "content" (ADC and TDC information) is small compared to headers and other timing marker words
 +
#* The current thought is to include both integral and peak into the data stream, as well as timing information
 +
#* Proposals have been made for the data format and they are under discussion
 +
#* The plan is to have a draft document in about a month that can be circulated more widely including to members of the fast electronics group. Ideally, the new firmware can be implemented by the time of the fall run.
 
# Reconstruction and Simulation (Tegan)
 
# Reconstruction and Simulation (Tegan)
 
#* Added tdc to the digiHit information in the simulation (similar to what was already included for adc hits)
 
#* Added tdc to the digiHit information in the simulation (similar to what was already included for adc hits)

Revision as of 14:13, 30 July 2015

Video Conferencing Information

Meeting Time: 11 a.m.

  1. To join via a Web Browser, go to the page [1] https://bluejeans.com/907185247.
  2. To join via Polycom room system go to the IP Address: 199.48.152.152 (bjn.vc) and enter the meeting ID: 907185247.
  3. To join via phone, use one of the following numbers and the Conference ID: 907185247.
    • US or Canada: +1 408 740 7256 or
    • US or Canada: +1 888 240 2560
  4. Upon connection all microphones are automatically muted. To unmute your mike on a Polycom or equivalent unit, enter *4. Unmuting on a computer is trivial as there is a microphone button than can be clicked.
  5. More information on connecting to bluejeans is available.

Participant Direct Lines

  • JLab Phone: in CC F326 is 757-269-6460 (usual room)
  • JLab Phone in CC L207 is 757-269-7084
  • Phone in the Regina Video-conference Suite is 306-585-4204
  • Athens Phone: in Christina's office is 011-30-210-727-6947

Action Items

  1. Change BCAL and FCAL coordinates use the global coordinate system (not the target center). Action of this item is under discussion

References

  1. FCAL HDFCAL log book
  2. BCAL HDBCAL log book
  3. BCAL Action Items and Working Tasks

Tentative Agenda

  1. Announcements
  2. Action Items
  3. Run preparations
  4. FCAL Update
  5. BCAL Update
  6. Calorimetry F250 Firmware Discussions
  7. Reconstruction and Simulation
  8. Calibration
  9. Any other business
  10. Testing

Minutes

Attendees: Manuel, Jon, Adesh, David, Elton (JLab); Will, Mike (CMU); George, Christina (Athens); Zisis, Noemi, Ahmed, Tegan (UofR)

  1. Announcements
  2. Action Items
  3. Run preparations
  4. FCAL Update
    1. Bases, firmware updates (Jon)
      • Hovanes is checking new firmware updates
      • Find bad bases in the detector that are corrupting other bases during bootloader uploads.
      • About 40 bad pmt bases found in the detector. Manuel: This problem encountered during installation and no fix determined, but Dan might be able to shed some light on it.
      • Even after reprogramming, the "bad" bases remain bad after reprograming.
      • Bad bases will be replaced next week and shipped back to IU for Paul to investigate problem.
    2. Analysis
      • Adesh: Changing focus to work on simulation with the goal to find the expected resolution from Monte Carlo.
      • Jon: Still plans to investigate FCAL efficiencies using various data samples including: omega-> pi0 gamma, omega-> pi+pi-pi0, pi0pi0p exclusive, pi0 p exclusive.
  5. BCAL Update
    1. BCAL Efficiency (Ahmed)
      • There have been some indications for phi dependence in the efficiencies, and discrepancies in layer 4
      • Christine: How to undertand efficiencies for layer 4 if tracks may stop in layer 3. Suggest selecting high energy tracks as a way of enhancing the probability for penetrating to layer 4.
      • David: Notes that the emulation code using mode 8 does not duplicate what is in the firmware for mode 7. Plans to submit some changes to the code to make them more compatible.
      • Elton: Layer 4 will be complicated to understand. Suggest that the focus be on differences between mode 7 and mode 8 efficiencies for layers 1-3.
      • George: Comments that the veff determination shows a layer dependence, not a phi dependence except for cosmics in the bottom half of the detector.
      • Will: does the phi modulation without energy selection in FCAL look the same as with an energy cut? Not yet investigated this.
  6. Calorimetry F250 Firmware Discussions
    • Elton summarized current discussion on the f250 firmware
    • The volume of "content" (ADC and TDC information) is small compared to headers and other timing marker words
    • The current thought is to include both integral and peak into the data stream, as well as timing information
    • Proposals have been made for the data format and they are under discussion
    • The plan is to have a draft document in about a month that can be circulated more widely including to members of the fast electronics group. Ideally, the new firmware can be implemented by the time of the fall run.
  7. Reconstruction and Simulation (Tegan)
    • Added tdc to the digiHit information in the simulation (similar to what was already included for adc hits)
    • Found that hdgeant was outputting negative times and an adjustment was needed to make them positive, as raw data only has positive integers.
    • Code was tested yesterday and plans to push changes to git soon.
    • Will: Considerations for eliminating negative hits from the clusterizer are under discussion.
  8. Git
  9. Calibration
  10. Any other business
  11. Testing