Revision as of 18:26, 9 September 2018

This page contains the procedure for checking if production runs are of good quality and can be used for physics analysis.

Run Periods

• RunPeriod-2016-02 Validation
• RunPeriod-2016-10 Validation
• RunPeriod-2017-01 Validation
• RunPeriod-2018-01 Validation
• RunPeriod-2018-08 Validation

Procedure

For each production run, do the following:

• Go to the | Offline Run Browser page.
• Follow the steps outlined in the checklist below.
• Certify that each section is okay
  • (DB + script to be developed)
• Set run status = 1 in RCDB
  • (script provided)

Run Statuses

• -1 - unchecked
• 0 - rejected (not physics-quality)
• 1 - approved
• 2 - approved long/"mode 8" data
• 3 - calibration / systematic studies

Checklist

Reference run for 2017-01: 30780

Reference run for 2018-01: 40933

• BCAL
  • Check Occupancy - Reference: [ link ]
  • Check Hit Efficiency - Reference: [ link ]
  • Check BCAL Recon. 1 - Reference: [ link ]
  • Check BCAL Recon. 2 - Reference: [ link ]
  • Check BCAL Matching - Reference: [ link ]

• CDC
  • Check Occupancy - Reference: [ link ]
  • Check Time-to-distance - Reference: [ link ]
  • Check CDC ROC amp - Reference: [ link ]
  • Check CDC ROC netamp - Reference: [ link ]
  • Check CDC ROC hits - Reference: [ link ]
  • Check CDC rawtime vs strawnum. - Reference: [ link ]

• FCAL
  • Check Occupancy - Reference: [ link ]
  • Check FCAL Hits 1 - Reference: [ link ]
  • Check FCAL Hits 2 - Reference: [ link ]
  • Check FCAL Clusters 1 - Reference: [ link ]
  • Check FCAL Recon. 1 - Reference: [ link ]
  • Check FCAL Recon. 2 - Reference: [ link ]
  • Check FCAL Matching - Reference: [ link ]

• FDC
  • Check Package 1 Occupancy - Reference: [ link ]
  • Check Package 2 Occupancy - Reference: [ link ]
  • Check Package 3 Occupancy - Reference: [ link ]
  • Check Package 4 Occupancy - Reference: [ link ]

• PS
  • Check Occupancy - Reference: [ link ]
  • Check Timing Alignment - Reference: [ link ]

• SC
  • Check Occupancy - Reference: [ link ]
  • Check SC Recon. 1 - Reference: [ link ]
  • Check SC Recon. 2 - Reference: [ link ]
  • Check SC Matching - Reference: [ link ]

• TAGH
  • Check Tagger Occupancy - Reference: [ link ]
  • Check TAGH Hits 2 - Reference: [ link ]

• TAGM
  • Check Timing ADC-RF - Reference: [ link ]
  • Check Timing T-ADC - Reference: [ link ]

• TOF
  • Check Occupancy - Reference: [ link ]
  • Check TOF Matching 1 - Reference: [ link ]
  • Check TOF Matching 2 - Reference: [ link ]

• RF
  • Check timing offsets - Reference: [ link ]
    • Should be centered around zero

• Timing
  • Check Calorimeter Timing - Reference: [ link ]
  • Check Drift Chamber Timing - Reference: [ link ]
  • Check PID System Timing - Reference: [ link ]
  • Check Tagger Timing - Reference: [ link ]
  • Check Track Matched Timing - Reference: [ link ]
  • Check Tagger/RF Timing - Reference: [ link ]
  • Check Tagger/SC Timing - Reference: [ link ]

• Analysis
  • Tracking 1 - [ link ]
  • Tracking 3 - [ link ]
  • Check BCAL pi0 - Reference: [ link ]
  • Check BCAL/FCAL pi0 - Reference: [ link ]
  • Check p+2pi - Reference: [ link ]
  • Check p+3pi - Reference: [ link ]
  • Check p+pi0g - Reference: [ link ]