Search results

Create the page "Popov" on this wiki! See also the search results found.

• JEF meeting, Nov 9, 2015
  ** A. Sitnikov, V. Popov may be available to help out with electronics.
  2 KB (357 words) - 17:14, 16 November 2015
• Instrumentation Publications
  # V. Popov, A. Somov, F. Klein, N. Walford, N. Sparks, ''Performance studies of Hamama
  19 KB (2,649 words) - 15:13, 11 July 2023
• Hodoscope Fabrication Readiness Review
  * Vladimir Popov (JLab, ESH)
  3 KB (398 words) - 12:00, 11 June 2013
• Follow up on the Hodoscope Fabrication Readiness Review
  * Vladimir Popov (JLab, ESH)
  4 KB (502 words) - 10:53, 30 September 2013
• GlueX TOF Meeting, October 18, 2016
  On Thursday of last week, we met with Vladimir Popov of RadCon. He designed the bases for the tagger hodoscope which have an on-
  4 KB (672 words) - 18:51, 18 October 2016
• GlueX TOF Meeting, June 28, 2016
  * The bases designed for the tagger by Vladimir Popov have amplification of a factor of 8 on board. They are AC-coupled and so ar
  4 KB (664 words) - 15:37, 28 June 2016
• GlueX TOF Meeting, July 19, 2016
  * Beni talked to Sasha Somov and Vladimir Popov about an amplifier in the PMT bases. He is concerned that the design for th
  3 KB (536 words) - 16:28, 22 July 2016
• GlueX TOF Meeting, September 20, 2016
  * '''New PMT bases with amplification'''. Mark paid a visit to Vladimir Popov to to discuss the possibility of using his design for the TOF. He was optim
  4 KB (618 words) - 18:36, 26 September 2016
• GlueX TOF Meeting, October 4, 2016
  Mark will arrange a meeting with Vladimir Popov next week to discuss PMT bases with amplification.
  2 KB (300 words) - 11:04, 18 October 2016
• GlueX TOF Meeting, November 29, 2016
  * Beni is collecting information to pass on to Vladimir Popov for his design.
  4 KB (694 words) - 19:43, 29 November 2016
• GlueX TOF Meeting, December 13, 2016
  * He has given specs to Vladimir Popov.
  2 KB (355 words) - 13:28, 14 December 2016
• GlueX TOF Meeting, February 7, 2017
  Beni has tested a prototype from Vladimir Popov. The results look good, though there is a signification DC offset at high r
  3 KB (448 words) - 15:26, 13 February 2017
• GlueX TOF Meeting, February 21, 2017
  ...rate_tests|tests with the new base]] with on-board amplifier from Vladimir Popov. (See his wiki page for details and plots.)
  4 KB (604 words) - 20:26, 25 February 2017
• GlueX TOF Meeting, March 21, 2017
  ...een re-soldered multiple times in the past several weeks. Finally Vladimir Popov had to supply a new board. He is currently working on a new board design sp
  6 KB (992 words) - 18:28, 21 March 2017
• GlueX TOF Meeting, April 18, 2017
  ...e next run and to continue studies of the new divider design from Vladimir Popov. The decision was based on the relatively stable performance of the tubes d
  2 KB (252 words) - 12:14, 18 April 2017
• GlueX TOF Meeting, May 2, 2017
  Vladimir Popov gave Beni board with 6 LEDs. Beni wants to collect light from the device in
  3 KB (433 words) - 14:00, 2 May 2017
• GlueX TOF Meeting, January 31, 2018
  ...er has a PMT with an amplifier in the base, designed and built by Vladimir Popov.
  3 KB (467 words) - 15:40, 1 February 2018
• JEF meeting, May 31, 2019
  ** Base divide/amplifier prototype design from V. Popov had too high amplification of 25 requiring operation of HV far below Hamama
  3 KB (458 words) - 16:41, 31 May 2019
• JEF meeting, September 6, 2019
  ** V. Popov will work with us this week to do tuning of divider design (amplification f
  2 KB (292 words) - 08:58, 9 September 2019
• PMT & Divider
  ...b.org/detectors/fcal2/pmt/NSS2012_JLAB.pdf New Active PMT Base for PbWO4 (Popov, H. Mkrtchyan, presentation at IEEE, Nov 2012)] :: Three active bases were modified by V.Popov. They were installed and testes using the CCAL
  4 KB (504 words) - 11:38, 28 November 2023